====== CP-IO22 PNP - IO Board Accessory for the ComfilePi 40 pin header ======

The CP-IO22 PNP is an IO board accessory for the [[comfilepi:index|ComfilePi]] consisting of 22 IO (11 bipolar inputs, 11 PNP outputs), screw terminals, and corresponding indicator LEDs.  It can be mounted to the rear panel of the CPi-A/B/S series panel PCs.

This product is not compatible with the CPi-C series panel PCs.

If you need NPN outputs, please use the [[:cpio:cp-io22:index|CP-IO22]].

{{ :cpio:cp-io22pnp:cp-io22pnp.png?nolink |}}

[[https://comfiletech.com/linux-panel-pc/|Coming Soon]]

{{ :cpio:cp-io22pnp:cp-io22pnp_io.png?nolink |}}


===== C#/VB.Net Control Example =====

The following is an example project illustrating how to program the [[:cpio:cp-io22:index|CP-IO22]] in C# or VB.Net using the [[:comfilepi:index#net_c_vbnet|Mono Framework]].  The same software can be used to control the [[ :cpio:cp-io22:index|CP-IO22]] or the CP-IO22 PNP.

{{ :cpio:cp-io22:cp-io22.mp4?700x400 |}}

[[https://github.com/COMFILE-Technology/ComfileTech.ComfilePi.CP_IO22.Demo|Source Code]]

This example application uses the following .NET libraries to control the digital inputs and relays.
  * [[https://www.nuget.org/packages/System.Device.Gpio/|System.Device.Gpio]]

===== Python Example =====

The pigpio library also has a [[https://abyz.me.uk/rpi/pigpio/python.html|Python interface]].

The following is an example illustrating digital inputs and outputs:

<code Python>
import pigpio

pi = pigpio.pi()

pi.set_mode(4, pigpio.INPUT)
pi.set_mode(17, pigpio.OUTPUT)

while True:
    if pi.read(4):
        pi.write(17, 1)
    else:
        pi.write(17, 0)

pi.stop()
</code>
===== Pin Map =====

The CP-IO22 pins are connected to the ComfilePi's GPIO header as shown below.

**Inputs:** GPIO 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 16\\ 
**Outputs:** GPIO 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27

{{ :cpio:cp-io22pnp:cpio-22_pnp_pinout.png |}}

===== Specifications and IO Circuitry =====

  *  Input Voltage: 5VDC (powered by ComfilePi's 5V pin)
  *  Current Rating: 100mA or more
  *  Humidity: 35 ~ 85% RH
  *  Temperature: -10 ~ 60 ℃
  *  Size: 128mm X 78mm

{{ :cpio:cp-io22pnp:cp-io22_pnp_circuit.png |}}

==== Inputs ====

  * Bipolar relative to COM x 11
  * Voltage Range: 12 ~ 24V
  * Absolute Min/Max Voltage Range: 3.3 ~ 28V
  * Response Time: 5ms
  * Input OFF Level: <1.8VDC
  * Input ON Level: >2.5VDC
  * Indicator LED OFF Level: <4.5V
  * Indicator LED ON Level: >5.0V

==== Outputs ====

  * DC Output Sink (PNP) x 11
  * Maximum Output Voltage: 24VDC
  * Response Time: 10ms
  * Current: 100mA
  * Minimum Load Resistance: 270Ω

:!: **To avoid damage to the product, please be sure to use a load resistance greater than 270Ω.**
===== Setting the Initial IO State =====

It may be necessary to modify the ComfilePi's initial GPIO output state to prevent the ComfilePi from turning the outputs ON when the ComfilePi boots.  

Modify the ComfilePi's ///boot/config.txt// file with the following configuration to set the initial IO state. See [[https://www.raspberrypi.com/documentation/computers/config_txt.html#gpio-control|GPIO control in config.txt]] for more information.

<code>
gpio=4-13=ip
gpio=16=ip
gpio=17-27=op,np,dl
</code>

[[:index|COMFILE Technology's Documentation Library]]