comfilehmi:water_resistant_front_panel_installation:index

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
====== Water Resistant Front Panel Model Installation ======

\\
 ==== CHA-070WR Panel Cutout ====

Recommended panel thickness: 1.6 to 5.0 (mm) [0.07 to 0.2 (in)].
A panel made from a strong material (e.g. stainless steel) will better protected against dust or water.

{{ :comfilehmi:water_resistant_front_panel_installation:cha-070wr_panel_cutout.png?nolink&500 |}}
 
\\

 ==== CHA-070WR Panel Mounting ==== 
Mounting brackets are supplied with each purchase. (Upper/Lower 2 ea.)

(Do not separate the bolt and the bracket. Leave the bolt inserted into the bracket as show in the image below.)

{{ :comfilehmi:water_resistant_front_panel_installation:hmi_bracket.png?nolink&200 |}}

1. Prepare a panel cutout according to the CHA-070WR dimensions, and insert the device into the cutout.

{{ :comfilehmi:water_resistant_front_panel_installation:install.png?nolink |}}

2. Insert the brackets into the bracket mounting holes as shown in the image below, pulling the bracket back to lock it into place.

{{ :comfilehmi:water_resistant_front_panel_installation:hmi_install.png?nolink |}}

3. Tighten the bracket mounting bolts to secure the device to the panel.
(CAUTION!! Over-tightening the bolts can cause deformation and/or damage to the device or panel.)

{{ :comfilehmi:water_resistant_front_panel_installation:hmi_install_2.png?nolink |}}


4. Repeat for each bracket, and verify that the product is properly mounted and secured to the panel.

{{ :comfilehmi:water_resistant_front_panel_installation:cha-070wr_mounting_4-1.png?nolink&400 |}}

===== Photographs =====

{{ :comfilehmi:water_resistant_front_panel_installation:dsc04012.jpg?nolink |}}

{{ :comfilehmi:water_resistant_front_panel_installation:dsc04013.jpg?nolink |}}

{{ :comfilehmi:water_resistant_front_panel_installation:dsc04015.jpg?nolink |}}


\\
 ==== CHA-102WR Panel Cutout ====

Recommended panel thickness: 1.6 to 5.0 (mm) [0.07 to 0.2 (in)].
A panel made from a strong material (e.g. stainless steel) will better protected against dust or water.

{{ :comfilehmi:water_resistant_front_panel_installation:cha_102wr_panelcutout.png?500 |}}

 
\\

==== CHA-102WR Panel Mounting ==== 
Mounting brackets are supplied with each purchase. (6ea)

(Do not separate the bolt and the bracket. Leave the bolt inserted into the bracket as show in the image below.)

{{ :comfilehmi:water_resistant_front_panel_installation:hmi_bracket.png?nolink&200 |}}

1. Prepare a panel cutout according to the CHA-102WR dimensions, and insert the device into the cutout.

{{ :comfilehmi:water_resistant_front_panel_installation:cha-102wr_mounting_1.png?nolink |}}

2. Insert the brackets into the bracket mounting holes as shown in the image below, pulling the bracket back to lock it into place.

{{ :comfilehmi:water_resistant_front_panel_installation:cha-102wr_mounting_2.png?nolink |}}

3. Tighten the bracket mounting bolts to secure the device to the panel.
(CAUTION!! Over-tightening the bolts can cause deformation and/or damage to the device or panel.)

{{ :comfilehmi:water_resistant_front_panel_installation:hmi_install_2.png?nolink |}}


4. Repeat for each bracket, and verify that the product is properly mounted and secured to the panel.

{{ :comfilehmi:water_resistant_front_panel_installation:cha-102wr_mounting_3.png?nolink&500 |}}

 \\

[[comfilehmi:index#ComfileHMI_Hardware| Back to ComfileHMI]]
User Tools

Site Tools

Page Tools
